VInstallation, Operation & Maintenance Manual(800) 237-4567·(727) 535-6339 · Fax (727) 539-8955 Advanced Protection Technologieswww.aptsurge.com ·
10OPERATIONDiagnostic Display PanelAll indicators and controls are located on the diagnostic panel. The diagnostic panel is located on the front of th
11appreciate SPD safety benets on smoke detectors, medical equipment, security equipment, etc. Similarly, some AHJ’s appreciate the nancial
accelerated on Wye systems where SPDs are designed for grounded systems. (SPDs for ungrounded systems generally have higher MCOV to allow for L-G volt
13Figure 12STANDARD & TYPE 4S MECHANICAL DRAWINGSIf an inoperate condition were to occur, the diagnostic display will indicate a problem via red S
FLUSH MOUNT & SCREWCOVER PULLBOX MECHANICAL DRAWINGSTYPE 4X NON-METALLIC MECHANICAL DRAWINGSFigure 13Figure 1421.62 [549.25]20.75 [527.05]20.00 [5
VManual de Instalación, Operación & Mantenimiento(800) 237-4567·(727) 535-6339 · Fax (727) 539-8955 Advanced Protection Technologieswww.aptsurge.c
E1 =NEMA 1/12/3R/4(medidas: 12 x 12 x 7,5” (305 x 305 x 191 mm))4X =NEMA 4X no metálica(medidas: 14 x 12 x 6” (356 x 305 x 152 mm))4S =NEMA 4X de acer
3Información Preventiva en cuanto a un DPSs en sistemas sin puesta a tierraCuidado – Los sistemas sin puesta a tierra son intrínsecamente inestables y
4Desembalaje e Inspección PreliminarInspeccione completamente el empaque en cuanto a daño o señales de mal manejo. Quite los materiales de empaque y a
5TIP: Las caídas de voltaje para líneas normales de 120V o 277V podrían ser 2-3V por cada cien pies (30 mts). En aplicaciones de sobretensiones, las c
2INTRODUCTIONThank you for choosing an APT Surge Protective Device (SPD). This is a high quality, high energy surge suppressor designed to protect sen
Para la electrónica sensible y sistemas informáticos, recomendamos que la medida de impedancia del sistema de puesta a tierra sea tan baja como sea po
El y XB’S de la Mayor parte de XA en recintos ‘cuadrados’ tiene las placas madre que pueden ser quitadas y colocadas de nuevo para reducir conduce. Mi
A cargas protegidas8INSTALACIÓNPlanique su instalacion. Usted necesitará cumplir con lo siguiente: ▪ Busque todas las Normas Nacionales y Locales (NE
GRÁFICOS ELÉCTRICOS PARA CONEXIONES TÍPICASSPLIT2 Hots, 1 Neu, 1 GrndHot (BLK)Hot (BLK)Neutral (WHT)VV}}Ground (GRN)WYE3 Hots, 1 Neu, 1 Grnd}Phase A (
OPERATIONPantalla DiagnósticaTodos los indicadores y mandos son localizados sobre el panel diagnóstico. El panel diagnóstico es localizado sobre el fr
11Retro-apto En Panel Existente sin Ola grande DisponiblePosicionesEstos pueden ser difíciles con opciones limitadas. Siga todo Códigos aplicables:•
MANTENIMIENTOLos DPSs requieren mínimo mantenimiento. Recomendamos inspección periódica de los indicadores de diagnóstico para asegurar la operación a
conectores se enchufan a cada módulo, transfiriendo la información a la lógica interna de a bordo ambos módulos. Si una condición de inoperate de ocur
14MONTAJE DE RUBOR Y SCREWCOVER PULLBOX DIBUJOS INDUSTRIUALESTIPO 4X DIAGRAMAS MECÁNICOS NO METÁLICOSFigura 13Figura 1421.62 [549.25]20.75 [527.05]20.
3Precautionary Statement Regarding SPDs on Ungrounded SystemsCaution – Ungrounded systems are inherently unstable and can produce excessively high lin
4Unpacking & Preliminary InspectionInspect the entire shipping container for damage or signs of mishandling. Remove the packing materials and furt
5and ensure that nearest breaker positions are used. If new construction, adjust breaker locations as appropriate.Tip: Voltage drops for normal 120V o
6For sensitive electronics and computer systems, we recommend that the ground impedance measurement be as low as possible. When metallic raceway is us
7the wall cavity 6 1/16” from the wall face such that the SPD is supported from its back. Note the mounting holes on the back ange. Also note that th
INSTALLATIONPre-Plan your installation. You will need to accomplish the following: ▪ Meet all National and Local codes. (NEC® Article 285 addresses SP
9ELECTRICAL DRAWINGS FOR CUSTOMER CONNECTIONSSPLIT2 Hots, 1 Neu, 1 GrndHot (BLK)Hot (BLK)Neutral (WHT)VV}}Ground (GRN)WYE3 Hots, 1 Neu, 1 Grnd}Phase A
Komentarze do niniejszej Instrukcji